08-14-2023, 06:56 PM | #67 |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
and its all similar but ur on your own, because I am doing a custom CCV for my S63 too with Troy, with no cross over junk tubes.. Why are you in such a rush, i think he can get this done in the next week or two.
If you have all the parts, you can do it as well, did you get the catchcans already, and all you need is the adapters for everything? Joe |
Appreciate
1
OscarX6M1.50 |
08-15-2023, 09:08 AM | #68 | |
Private First Class
35
Rep 187
Posts |
Quote:
So working on this... Looking for this fitting on an S63 .... just trying to be fully prepared when I get back to it tomorrow. can anyone tell me where this bad boy is It looks like its comes off the intake But when i was digging around yesterday I didnt see it unless I was distracted with other things. |
|
Appreciate
0
|
08-15-2023, 10:51 AM | #69 | |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
Quote:
Sophisticated Redneck will come through and even send you just want you are missing to make it work, if you can post what parts you already have. |
|
Appreciate
0
|
08-15-2023, 01:26 PM | #70 |
Private First Class
35
Rep 187
Posts |
I do appreciate.. your support of Troy, But I am severely limited on TIME, I am using this as a stop gap measure till I get settled after my move ( pretty solid rear main seal leak and valve cover leak)... I have everything purchased... Per troys orginal Post ... I now just need to figure out 2 last things...
1. do the S63 intakes need to be removed.. 2. where do I tap the 6an to 1/8th NPT into so I can run the lines... as they are different than N63... I dont think I need any parts left to make it work I just need to confirm locations before I hack something and am left with the car unable to operate.. |
Appreciate
0
|
08-15-2023, 01:27 PM | #71 | |
Private First Class
35
Rep 187
Posts |
Quote:
Sorry the PM where troy send you more information on the S63? Last edited by punisher12b; 08-15-2023 at 01:37 PM.. |
|
Appreciate
0
|
08-17-2023, 11:59 AM | #72 |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
THis is what we're doing, you can go with plastic but we have nice AN fittings to make it look real. I will send you a PM, but the S63 CC do not work well, because of the shared tube, its all over the web that only the drivers side works, and little oil in the passenger, hence why Troy and I are building isolated CCVs for each side of the motor.
|
Appreciate
1
OscarX6M1.50 |
08-17-2023, 01:35 PM | #74 | |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
Quote:
S63 does and the passenger side will not catch any vapor, its documented all over the web. You have to convert a S63 system to an isolated system for the CCVs to work correctly and catch on both intakes. |
|
Appreciate
1
OscarX6M1.50 |
08-17-2023, 05:34 PM | #75 | |
Private First Class
35
Rep 187
Posts |
Quote:
OK so I will rephrase what I asked, If you follow the instructions outlined here.. it removes the crossover.. does it not then isolate the the two banks? I get you say its well documented over the internet.... but could you answer that question.. on the install that I did I removed the crossover, and tapped the line pulling vacuum on the passenger side.. So I ask again. how is my system not isolated? |
|
08-17-2023, 06:05 PM | #77 |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
this is the isolated setup. just an eyesore for what i would do, hence why we are doing an OEM look style, but you have it right, they are isolated, did you set the vacuum right? next is to see if both sides collect the same amount of oil at each interval of oil change.
|
Appreciate
1
OscarX6M1.50 |
08-17-2023, 06:35 PM | #78 | |
Private First Class
35
Rep 187
Posts |
Quote:
Yes vacuum is now set to -9 yeah a few rando connections cause I didn't check my amazon order.. and i needed to make adjustments its what the speed shop had... so as opposed to be sitting there without a car I finished it...I will clean it up when I get moved at the end of the month... but it was more important to get it on the road and running so I could get to my divorce attorney who notified me while I was working on it my X finally sent a reasonable separation agreement soooo crazy underhood and cleaning up later is WAYY worth to be divorced asap... |
|
08-17-2023, 06:41 PM | #79 | |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
Quote:
Date in chapters, for the rest of your life, happy for life.. Matrix is a powerful machine to sell more rings, dresses and status. |
|
Appreciate
1
OscarX6M1.50 |
08-17-2023, 07:22 PM | #80 |
Private First Class
35
Rep 187
Posts |
Thanks.. sometimes life works out that way..
On to my oil leak guessing game. lol I just dont have the time so I left it a buddys shop.. I have to move from D.C to TN on the 28th... sooo hope what ever it is we can get the parts for. I started a fun thread lol |
Appreciate
1
OscarX6M1.50 |
08-17-2023, 07:28 PM | #81 | |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
Quote:
|
|
Appreciate
1
OscarX6M1.50 |
08-17-2023, 08:37 PM | #82 | |
Private First Class
35
Rep 187
Posts |
Quote:
if i romp on it ill drench the belly pan and the oil gauge will drop 1/4 I know i have a rear main seal and valve cover gasket leak... gonna get my buddy to bore scope it tomorrow. |
|
Appreciate
0
|
08-19-2023, 08:43 AM | #83 | |
Private First Class
35
Rep 187
Posts |
Quote:
the gauges all of them I found seem to use what I am used to vacuum lines to read the +/- and we need to run 2? This picture though shows an electrical connection on the barb? also whats your ebay store I was gonna see if I can grab a vent pod mount Last edited by punisher12b; 08-19-2023 at 10:21 AM.. |
|
Appreciate
0
|
08-21-2023, 07:50 AM | #84 |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
Another update on the best CCV setup for any BMW Motor.
Master Genius Troy is nearly complete with the project. Anyone interested in a real system, that looks OEM, and has the performance to back it up, post here, Im sure would be great to get his hard work out on the street. Joe |
Appreciate
1
OscarX6M1.50 |
08-23-2023, 12:45 PM | #87 |
Builder of Special Cars
224
Rep 518
Posts
Drives: G12 B7,F02 750li,E70 X5M,E46M3
Join Date: May 2013
Location: Dallas, TX | Farmington, UT | Gainesville, FL
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|