11-12-2023, 07:53 PM | #1 |
New Member
2
Rep 5
Posts |
Anyone upgrade to aluminum transmission pan?
I just tried installing one on my 09 x5d e70 and turns out its not notched enough for clearance for the solenoid wiring harness. Torquing it down heard a crunch new knew that couldn't be good, pulled it off and compared. Anyone else experience that? Looking for a replacement harness, no part number hard to find if anyone has one kicking around. Thanks
|
11-12-2023, 10:38 PM | #2 |
Colonel
4941
Rep 2,995
Posts
Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal
iTrader: (2)
Garage List 2006 BMW 330i [8.21]
2009 BMW 328i Touri ... [7.90] 2013 BMW X5 35i [7.63] 2011 BMW 528i [8.75] 2006 Mazda3 [5.50] |
Oh no!!!! Hope it's not too much time/hassle/money to repair!
|
Appreciate
0
|
11-13-2023, 06:59 PM | #3 |
First Lieutenant
250
Rep 391
Posts
Drives: 2006 M5, 2012 X5d, 2008 E91
Join Date: Aug 2012
Location: Seattle
|
What part number did you buy? I thought ucsbwsr used the aluminum pan from the X5m transmission w/ the serviceable oil filter on his. Don't recall if he mentioned any modifications were needed or not. I think I remember seeing it on his build thread but I'm too lazy to go searching for it.
|
Appreciate
0
|
11-17-2023, 10:29 AM | #5 |
First Lieutenant
250
Rep 391
Posts
Drives: 2006 M5, 2012 X5d, 2008 E91
Join Date: Aug 2012
Location: Seattle
|
Found the post.
https://www.xbimmers.com/forums/show...&postcount=237 URO I've heard is hit or miss on a lot of stuff. |
Appreciate
1
StradaRedlands4940.50 |
11-17-2023, 10:38 PM | #6 | |
Colonel
4941
Rep 2,995
Posts
Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal
iTrader: (2)
Garage List 2006 BMW 330i [8.21]
2009 BMW 328i Touri ... [7.90] 2013 BMW X5 35i [7.63] 2011 BMW 528i [8.75] 2006 Mazda3 [5.50] |
Quote:
https://www.fcpeuro.com/products/bmw...an-24117588752 https://www.fcpeuro.com/products/bmw...-24152333899kt |
|
Appreciate
0
|
11-18-2023, 10:40 AM | #7 |
First Lieutenant
250
Rep 391
Posts
Drives: 2006 M5, 2012 X5d, 2008 E91
Join Date: Aug 2012
Location: Seattle
|
I have zero experience with it other than reading ucsbwsr's build thread. He is normally pretty good about stating what modifications need to be made if any, and he didn't say anything about modifying the pan. So I would assume it's a straight bolt on.
|
Appreciate
1
StradaRedlands4940.50 |
11-18-2023, 07:45 PM | #8 |
Colonel
4941
Rep 2,995
Posts
Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal
iTrader: (2)
Garage List 2006 BMW 330i [8.21]
2009 BMW 328i Touri ... [7.90] 2013 BMW X5 35i [7.63] 2011 BMW 528i [8.75] 2006 Mazda3 [5.50] |
Well I am intrigued! I like the idea of the larger heat-sink on it, no other real need for it beyond that. Thinking, thinking, thinking...
|
Appreciate
1
jbash87249.50 |
11-19-2023, 11:33 AM | #9 |
First Lieutenant
250
Rep 391
Posts
Drives: 2006 M5, 2012 X5d, 2008 E91
Join Date: Aug 2012
Location: Seattle
|
Larger heat sink is what I'd be looking for from this, especially with the towing I do. Having a replaceable filter is a bonus as well. I'll most likely be doing this mod when I need to replace my tranny fluid in another 10k miles or so.
|
Appreciate
1
StradaRedlands4940.50 |
11-19-2023, 12:19 PM | #10 |
Colonel
4941
Rep 2,995
Posts
Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal
iTrader: (2)
Garage List 2006 BMW 330i [8.21]
2009 BMW 328i Touri ... [7.90] 2013 BMW X5 35i [7.63] 2011 BMW 528i [8.75] 2006 Mazda3 [5.50] |
I don't tow, but drive in a hot climate. Heat dissipation is a good thing! This on the tranny and a remote oil cooler would make the X's life a better one!
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|