07-29-2019, 09:34 PM | #1 |
Private
7
Rep 86
Posts |
Zero Quantity Adaption Cylinder 6
Hey guys....
Started getting this code 004b25 thar last week. Read up on it and i am confused....do i need to replace the injector or adjust the adaption? I also read that the adaption will adjust itself over time. Does that mean this might go away on its own? The car drives fine...i don't notice anything. 2013 x5 35d. Any advice is appreciated. Hartwa |
07-29-2019, 09:52 PM | #2 |
i'm just saying
5749
Rep 2,634
Posts |
normally such an error cause rough idle but you re saying car runs fine.. adaption is a never ending relearning process that yes it might go away as you ve said but im not sure it ll take away the codes also.. if i were you i d keep eye on idle closely and do nothing until feeling lose of power or idle changes..
__________________
"Race car driving is like sex. All guys think they're good at it." Jay Leno
|
Appreciate
0
|
07-30-2019, 09:34 AM | #3 |
Enlisted Member
0
Rep 41
Posts |
Deleted? Have the injectors ever been replaced? I'm not sure if adaptation values can be "adjusted" manually, maybe reset. I would first make sure the injector codes are correct.
I was getting this error (cylinder 3) and the only thing that fixed it was swapping the injector codes 2<=>3 then driving for a few days then swapping them back. I read that the dde is the actual culprit and doing this made the dde recognize the values. If you don't have ista definitely get it. |
Appreciate
0
|
07-30-2019, 11:36 AM | #4 |
Private
7
Rep 86
Posts |
Thanks both of you.....i wil just keep driving it for now and see...
...i do have carly for bmw and i think i got ista on my labtop but never used it....i am pretty sure i bought a cavle for it. |
Appreciate
0
|
09-09-2019, 09:31 AM | #5 |
Private
7
Rep 86
Posts |
Been over a month and i am tired of seeing that check engine light. I will try swapping the codes with ista. I am a nube with this program... an anyone recomend a tutorial?
|
Appreciate
0
|
09-11-2019, 01:45 PM | #7 |
Lieutenant
211
Rep 433
Posts |
What do you mean by swapping codes?
Have you reset the adaptations for injector 6? You'll need an icom cable as the kdcan cable is too slow
__________________
2012 X5d | Deleted & BRR Tuned | DWR TCU Tune | 10.25" Android 8.1 Screen
Build Thread https://www.xbimmers.com/forums/show....php?t=1529213 |
Appreciate
0
|
09-13-2019, 12:24 PM | #9 |
Private
7
Rep 86
Posts |
I forgot to mention that i cleaned the intake manifold when i changed out a vacuum solenoid a few months ago. I have read that people have to do a wheel reset adaption after a carbon clean....
I am also getting a smoothness error in that cylinder along with the zero quantity adaption. |
Appreciate
0
|
11-05-2019, 01:23 PM | #11 |
Lieutenant
211
Rep 433
Posts |
what's the coolant temp after a 20-30 min drive on the highway?
__________________
2012 X5d | Deleted & BRR Tuned | DWR TCU Tune | 10.25" Android 8.1 Screen
Build Thread https://www.xbimmers.com/forums/show....php?t=1529213 |
Appreciate
0
|
11-08-2019, 07:56 AM | #15 |
Private
7
Rep 86
Posts |
Awesome.... I had to replace mine on my 335d (same engine). That one i noticed in the fall would not blow warm enough air.
I will get it ordered today and let you know how it works out after I install it...thanks again. |
Appreciate
0
|
11-08-2019, 05:22 PM | #16 |
Private
7
Rep 86
Posts |
Just curious.... what is the link between the zero quanity injector code and low coolant temp? I did notice that when i worked reset the check engine light it would usually come back after the engine was warm...never on a short trip.
|
Appreciate
0
|
11-09-2019, 02:53 AM | #17 |
Lieutenant
211
Rep 433
Posts |
The friction produced during opening and closing of the piezo injectors causes wear on the nozzle seat of the nozzle needle. This changes the injection quantity over the service life, which is compensated for by correcting the actuation duration. Injection quantity correction comprises the following:
• Zero quantity calibration • Main injection quantity correction The following function requirements are required for this: • Engine speed between 1,000 and 2,600 rpm • Deceleration mode or driving operation greater than zero • Engine oil temperature greater than 80 °C That's for CDI but it gives you an idea. Our motors run at 88c instead of 80 on CDI
__________________
2012 X5d | Deleted & BRR Tuned | DWR TCU Tune | 10.25" Android 8.1 Screen
Build Thread https://www.xbimmers.com/forums/show....php?t=1529213 |
Appreciate
0
|
11-11-2019, 10:01 PM | #18 |
Private
7
Rep 86
Posts |
That fixed it....got it in last night and went to work and back without the light coming back on. First time it did not come back on in 4 months. Thanks a lot for the help...really appeeciate it. Dealer is an 1.5 hr drive...so this saved me an all day trip to get it fixed...
Thanks again |
Appreciate
0
|
11-24-2019, 08:50 PM | #20 |
Enlisted Member
0
Rep 41
Posts |
Swap #5 and #6 injector codes, delete faults, drive for a few days, then swap them back. This worked for me but then I had the injectors out prior to getting the fault so I had recoded all injectors.
|
Appreciate
0
|
11-25-2019, 09:26 PM | #21 |
Private
7
Rep 86
Posts |
I try it this weekend but i curently have inpa and a Pro kdcan cable from bimmer geeks. Can i do it with that? i know you mentioned getting ista... do i need a different cable?
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|